I am an N scale model railroader and I have decided to not make the switch to DCC. Most of my engines are pre-DCC and not DCC ready. There isn’t much room in an N-Scale engine to put anything without cutting out some of the innards. Also model railroading is nostalgic. I grew up in the seventies and I remember the power pack to have was the MRC Golden 501. I found one (501N) a few years ago in new condition and bought it instantly. Also if I have a problem, I can track it down and figure it out. When my friend bought a locomotive with a decoder and asked me to fix it, I told him to return it. I have rebuilt trucks with new gears, changed brushes etc. but DCC I don’t know about. Now, heaven forbid, if my house burned down and I lost all of my stuff, I’d start over with DCC. Also, I like the KISS principle. Anyone else decide to stay with the old technology?
Yah, me too–I’ve got quite a few DCC-ready locos, but I’ve got an awful lot of older brass (which I run) and by the time I could get (or afford, for that matter) everything converted, my grandson would have grandkids! So this old fart is sticking with cab-control and enjoying it.
Tom[}:)][}:)]
DCC offers simplified block wiring, unlimited cabs, and optional sound…
I know how to wire, understand electricity
Am 99.9% single person operation (or one guest)
Have Wireless Cabs (2)
- Variable momrnentum - and decay,
- Adjustable starting voltages
- Soundtraxx Steam & DIesel Onboard sound
Under table dual voice coil Sub woofer system
DCC anybody?
Sountraxx is designing an under-table ‘Surround Sound’ system for 5.1 – 7.1 sound systems with N scaleers in mind. Before ordering, think of 4 - 6 speakers under the layout and realistic sound limited only by the cost of the sub-woofer.
I had very little invested in the world of DC, so it was an easy decision fo rme to go to DCC and one I do not regret at all. However, I can fully appreciate why you might not want to switch. I can tell you, that some of the HO DCC installs are not easy, so I can’t imagine how hard an N scale would be.
I’m sticking with DC for now although I did wire my layout for simple conversion if i decide to change. Budget is the biggest consideration right now .
At this point, DC is better. Some locos are already so light, I’d have to remote the loco in boxcar or use another pickup source. If my wife was going to run trains at the same time, might consider it. Someday, might make the layout selectable, DC or DCC, buy locos with DCC, but they’d all need to be cab units, F7A/B such. I can’t imaging my N scale Kato RS-2 with DCC, it would need element 102 or higher as weight to pull 10 cars.
What I AM considering is how to automate track power in the blocks before/after a train as it moves without stopping it, and control signalling. But I’m doing a layout in a small bedroom, less than a scale mile linear run. I can’t really run more than 1 train at a time, even if the other is on auto pilot, and the track plan might support 4 or 5 trains moving someday, maybe 3 if I pull power off another section.
Not going to get more space unless the next Kato release is a Monorail passenger set.
Los Angeles to Las Vegas bulet train on dedicated pylons 2-3 stories up.
I myself have absoultely no intrest in going to DCC. My layout is too small for me to invest that kinda money into it. I understand the potential of DCC but I have limited funds and I would rather put the money into something else(like more trains). If I ever were to have a larger layout and more money then I may consider ir but defintely not now.
Jeremy
If you want to go the DCC route in N scale, you basically have to switch to all new engines. Period. It’s REALLY difficult to convert most of the old (pre-1985/1990) N scale diesels to DCC, and physically impossible to convert some (Trix FA’s with all-metal shells that route power, for example). Unless you’re REALLY into DCC, and not a casual used (the majority of DCC users), there’s no way you’ll want the hassle of converting a large, old fleet. Steam of course is easier, with the tenders being a great place to stuff a decoder, but N scale steam is a big minority.
I’m sticking with DC for now on my HO home layout, but only because I’m nowhere near ready to start running trains on a regular basis. I am getting ready for the day I switch to DCC however, by replacing the bulk of my engine fleet with newer, DCC-ready/friendly/installed engines. Cab control for a large walkaround layout needing at least 10 cabs is a bite to try to wire, and I’ll save money and stress with DCC.
Running more than one engine at a time is multitasking, I multitask all day long. When I get home I want to be able to just concentrate on one thing at a time, I will be sticking with DC.
Tom
tom and tom-fiatfan / white [#ditto][#ditto][#ditto][#ditto]
I would go with DCC if it were’nt so expensive. I have 116 diesel and 3 steam. About 8 are DCC ready. It would be alot of work also. Just got my first BLI with sound and it seems to be really cool, but you cant MU it with anything else. The price of technology. Joe A.
of course, i like the idea of throwing pole switches and controling my trains indirectly
I could stick with DC, but I suppose I could keep all of my Athearn BB loco’s and freight cars from 20-30 years ago. I made the decision to sell off everything and invest in DCC, and new Kato/P2K/Atlas engines & P2K/Atlas/Red Caboose/Accurail/etc freight cars. Most of my Athearn had new n/s wheels, detail,& painted correctly(engines as well as freight cars). Of those 100+ engines, 400+ freight cars; I really only used maybe 15-20 engines and less than 100 cars on the layout. The rest were displayed or boxed up.
I now have 37 engines(oldest is an Atlas/ER Models FP7). Only about 16 have decoders - just what I really need to run the railroad! Some of my engines/cars will be in a display case for the most part. I now have less than 100 ‘high end’ freight cars, and could use more; but that will come as I complete ‘projects’.
Now this gets us to DCC. When I went to DCC in the late 90’s, I just flipped all of the panel toggles to cab A and hooked up the system. I am now running a DCC bus, and am pulling about 2000 ft of #18 block control wiring, and 40+ toggles. DCC has made operation so much better, but I have to agree that conversion is still expensive. Conversion costs look big because of the need to buy a command station/booster &
thottles. Then there is all of the expense/work of installing decoders. Just the sight of all that work is enough to chase some folks away. The bottom line is that I feel good about all of the work I have done over the past 3 years of serious conversion/upgrading.
And I would do it again - running train is so much better - those new engines do preform realy great! As I said in the beginning of this post, I could stay with DC; but I really had built everything I wanted, and had a real mixed collection of equippment. This project has rejuvinated my interest in modeling as well.
Jim Bernier
As a First time layout builder I have looked at several factors when I decided on how I was going to wire my layout. Since it is a traditional 4X8, I decided that it would be more cost effective and for me alot easier to wire, 5 blocks, than to go through the hassle of setting up a DCC system. I plan on running two cabs at the same time, one in an oval and the other one taking on switching duties. Though all the bells and whistle that a DCC system offers are really appealling, I’m going DC for now.
I don’t want anyone to think I’m ANTI-DCC–I’ve seen several of the layouts and I’m really impressed. However I have over 40 brass steamers that I’m using (and I mean USING!), I said the Hell with Multi-tasking when I retired (worked with a woman who ran my department that was a Multi-tasker and guess what–everything got HALFWAY done, and that was about it!), and I can still run more than one train on my DC layout if I choose (which I don’t, after the last rear-ender). So I’m happy where I am. the thought of the expense of decoders for 40 brass engines is just too daunting for me at my age.
Tom
I am getting back into the hobby after many more years then I want to admit, so the decision was easy for me, DCC, no discussion there at all.
I can readily understand the position of those who have lifetime of investment in older locos that cannot be adapted to DCC. It is also apparent to me that many modelers just don’t have the funds to invest in DCC, so DC is certainly the right answer for them.
I wonder however, if those who have older setups that cannot be converted to DCC, have the room to set up a newer table with DCC to get the enjoyment of using DCC? Run both in otherwords.
All of my N-Scale is within 3 years of being new, but I have no need or desire to go DCC.
The only shortcoming I have with my present layout is I don’t have enough tracks to park more engines than 2. This is OK with me as the rest can sit in my display case until I want to use them. And since 99% of the time I’m the only one operating the layout, I feel there is no need for DCC.
I have operated on several layouts with DCC and have really enjoyed myself. These layouts however are very large with several operators running several trains at one time.
(V&O, AGE, L&N Henderson Sub.)
If I were to start over in H-O scale I would probably go with DCC and purchase most of my new engines with decoders already installed. But I would have to be building a large enough layout for more than 1 operator.
The last big layout I had was built with 2 throttles (GML) and had double-pole, double-throw toggle switches that would control the few blocks I had and this worked great.
I too subscribe to the “KISS Principle.”
But there is no way in heck I’m going back and try to mount decoders in my N-Scale engines!!!
So I will be sticking with DC cab control for a long time.
I do get a chuckle when I read about all the problems people are having with their DCC!
gtr
I still use a conventional DC throttle, too, to operate a 9’ x 3’ (with a 3’ "L "extension) switching layout. Even the Bachmann DCC is too expensive for me, at this time. The unit plus a decoder for each engine would result in serious deficit spending! I’d rather pick up an Alco S-1 or VO-660 right now. My newer engines, especially, run really well with regular DC, and I can’t run more than one at a time, anyway. Maybe in the future, we’ll see.
Best
smyers
I’m sticking with DC.
Too many BB Athearns to want to switch to DCC, besides, after finally getting some wiring done last night, I actually had two different trains running at the same time.
I don’t need to run more than 2 trains at once.
Gordon
I rejoined this hobby after 20 years out of it. I like the DCC technology but I went with a 2 cab DC set-up mainly due to cost of DCC. My layout is going to be mostly a one man operation so DC cab control will work well for me.